In recent years, with the improvement of the level of science and technology, the functions of the fast rolling shutter door are constantly improving. At the same time, we must pay attention to the debugging and testing of the main functions of the fast door. In general, the functional debugging and testing work of fast rolling shutter door is generally carried out from the following aspects, and the specific detection methods are as follows:

1、急停按钮功能检测

1. Function test of emergency stop button

急停按钮的作用是当快速卷帘门体运行时发生紧急情况而特别设计的，它对于人身的保护具有积极作用。进行快速门急停按钮功能检测时，可以在门体运行过程中，按下这一急停按钮，看快速门门体是否立即停止。若门体没有立即停止，就需要检查原因，看急停按钮是否失灵或损坏，损坏的及要修理。

The function of emergency stop button is specially designed in case of emergency when the fast rolling shutter door is running. It has a positive effect on the protection of personal safety. When testing the function of the emergency stop button of the fast door, you can press the emergency stop button during the operation of the door body to see whether the fast door body stops immediately. If the door does not stop immediately, it is necessary to check the cause to see whether the emergency stop button is out of order or damaged, and the damaged one should be repaired.

2、红外防砸性能调试

2. Debugging of infrared anti smashing performance

红外防砸功能也是快速卷帘门的保护装置。检测时，可以在湖北高速门门体下落过程中，切断红外对射系统，看快速卷门门体是否及时反弹上升开门位置。注意：进行红外防砸功能测试时，一定要注意自身，防止红外系统失灵造成意外事故。

The infrared anti smashing function is also the safety protection device of the fast rolling shutter door. During detection, the infrared radiation system can be cut off during the falling process of Hubei high-speed door body to see whether the fast rolling door body rebounds and rises to the opening position in time. Attention: when testing the infrared anti smashing function, you must pay attention to your own safety to prevent accidents caused by infrared system failure.

3、自动开启功能检测

3. Automatic opening function detection

自动开启是快速卷帘门深受工业企业用户喜爱的原因之一，也是高速卷帘门非常主要的功能之一。检测这一功能，可以利用车辆、人员移动来模拟实际状况，以=观察门体是否能够及时开启以及是否全角度无死角信号覆盖。

Automatic opening is one of the reasons why the fast rolling shutter door is deeply loved by industrial enterprise users, and it is also one of the main functions of the high-speed rolling shutter door. To detect this function, we can use the movement of vehicles and people to simulate the actual situation, so as to observe whether the door can be opened in time and whether there is no dead angle signal coverage in all angles.

4、上下限位调试检测

4. Upper and lower limit debugging detection

上下限位位置关系着高速门的日常使用，一旦位置不准确造成快速卷帘门开启、关闭不到位，那快速门的密封功能就无法得到保证。进行上下限位测试时，可以在门体静止状态下，按下上升按键，门体向上运行，待经过缓冲、完全停止后，判断提升高度是否满足使用方要求。如不满足要求，再次进行调试。依照同样的方法，按下降按键，待门体下落完全停止后，检查PVC快速门门体末端停留位置是否到位，不到位的及时进行调整。

The upper and lower limit position is related to the daily use of high-speed door. Once the position is not accurate, the fast shutter door can not be opened and closed in place, so the sealing energy-saving function of the fast door can not be guaranteed. During the upper and lower limit test, when the door body is still, press the up button to move the door upward. After buffering and stopping completely, judge whether the lifting height meets the user's requirements. If the requirements are not met, debug again. According to the same method, press the down button and check whether the stop position of the PVC fast door end is in place after the door falling completely stops. If not, adjust it in time.