Remote control garage door is to use the remote control to switch the garage door directly. You don't need to open it manually. Now the opening distance of garage door is 20-30 meters, which fully meets and meets the needs of owners. Just press the button on the remote control to easily enter the garage door. Occasionally, the garage door will get angry, and there will be some faults, many of which are caused by the operation manual.

1.如果门没有关闭，它将自动反转操作或在门打开时停止操作而不接触行程开关。可能的原因如下：开关门阻力大于启动障碍物感应系统的开启和关闭负载力的设定，并且连杆长度调节不当。解决方案：拉开离合器装置，检查门体和扭簧是否平衡，开合是否灵活，增加开合负载力，并在门关闭时调整连杆长度。

1. If the door is not closed, it will automatically reverse operation or stop operation when the door is open without touching the travel switch. The possible reasons are as follows: the resistance of opening and closing the door is greater than the setting of opening and closing load force of starting obstacle sensing system, and the length of connecting rod is not adjusted properly. Solution: open the clutch device, check whether the door body and torsion spring are balanced, whether the opening and closing are flexible, increase the opening and closing load force, and adjust the length of connecting rod when the door is closed.

2.手动开关或遥控器无法启动驱动器。查看驱动器是否已连接到电源。手动开关或遥控接收器打开。运行次数太高，导致电机受到热保护。检查插座，插头，手动开关，保险丝。保险丝，检查手动开关和遥控接收器接线，重新定位行程开关以增加行程。

2. The driver cannot be started by manual switch or remote control. Check to see if the drive is connected to power. The manual switch or remote control receiver is on. The motor is thermally protected due to too many running times. Check the socket, plug, manual switch and fuse. Fuse, check wiring of manual switch and remote control receiver, and reposition travel switch to increase travel.

3.门不紧或门不完整。可能的原因是：行程开关的位置未正确调整，行程开关可以重新定位以增加行程。

3. The door is not tight or the door is incomplete. The possible reason is that the position of the travel switch is not adjusted correctly, and the travel switch can be repositioned to increase travel.

4.手动开关可以控制驱动装置和遥控器不能，原因是：遥控器不正确，遥控系统有故障，解决方法：按照说明完成代码操作，更换遥控器内部电池，如果不可能，请维修人员检查接收控制板。

4. The manual switch can control the drive device and remote controller. The reason is that the remote control is incorrect and the remote control system is faulty. Solution: complete the code operation according to the instructions and replace the battery inside the remote control. If it is impossible, please ask the maintenance personnel to check the receiving control board.

遥控车库门常见的故障怎么修理

How to repair the common faults of remote garage door

5.由于行程开关损坏或行程开关线打开，门体超出行程开关，检查行程开关和行程开关接线。

5. Because the travel switch is damaged or the travel switch line is opened, the door body exceeds the travel switch. Check the travel switch and travel switch wiring.

6.门体单向行程开关损坏或行程开关线短路。可能原因：光电开关在光路上有障碍物。负载力调整不到位。解决方案：检查行程开关和行程开关接线，以光电形状。光路上的障碍物，重新调节打开和关闭负载力。

6. The one-way travel switch of door body is damaged or the line of travel switch is short circuited. Possible cause: the photoelectric switch has obstacles on the light path. Load force adjustment is not in place. Solution: check the travel switch and travel switch wiring to clear the photoelectric shape. Obstacles on the light path, re adjust the opening and closing load force.

7.驱动装置正常运行，但门体不运行，造成的原因有：滑架上的离合器没有复位，启闭负载力调节没有到位，解决方案：复位离合器，重新调节启闭负载力。

7. The driving device operates normally, but the door does not work. The causes are: the clutch on the sliding frame is not reset, and the opening and closing load force is not adjusted in place. Solution: reset the clutch and readjust the opening and closing load force.

8.车库外遥控器作用距离明显低于10米，车库屏蔽严重，造成的原因：电池电力不足解决方案：将天线延长车库外部，将天线伸出驱动器外部并拉直，更换电池。

8. The operating distance of the remote control outside the garage is obviously less than 10 meters, and the garage is seriously shielded. The reason is that the battery power is insufficient. Solution: extend the antenna to the outside of the garage, extend the antenna out of the driver and straighten it, and replace the battery.

9.门体运行噪音过大，造成的原因：五金件安装不牢固，驱动装置拉杆没有位于门体线上，门体运行导轨不平行，合页，滚轮处没有涂覆陶瓷。解决方案：坚固五金件，调节驱动装置拉杆与门体线重合，调节门体运行导轨相互平行，在合页，滚轮处覆陶瓷。

9. The causes of the excessive noise of the door body are as follows: the hardware is not firmly installed, the pull rod of the driving device is not located on the center line of the door body, the guide rail of the door body is not parallel, and the hinge and roller are not coated with ceramic. Solution: solid hardware, adjust the driving device pull rod to coincide with the center line of the door body, adjust the running guide rail of the door body to be parallel to each other, and cover the hinge and roller with ceramics.

以上都是远程车库门的常见故障和相关解决方案。遇到上述故障时，您可以根据这些方案处理它们。如果您无法解决问题，可以请人士处理。为了减少车库门的故障，我们必须定期维护车库门。

The above are the common faults and related solutions of remote garage door. When encountering the above faults, you can deal with them according to these schemes. If you can't solve the problem, you can ask a professional to deal with it. In order to reduce the failure of the garage door, we must regularly maintain the garage door.