欢迎光临济南市天桥区昌达卷帘门加工部官网!

联系我们 收藏本站 在线留言

新闻资讯

首页>>新闻资讯>>高档车库门常见故障及处理方法
新闻资讯
联系我们
济南市天桥区昌达卷帘门加工部

联系人:刘经理

电话:15953131568

网址:http://www.jnhsjlm.com

地址:济南市天桥区金牛建材市场

高档车库门常见故障及处理方法

来源:http://www.jnhsjlm.com 日期:2021-08-10 发布人:hongshun
高档车库门常见故障及处理方法如下
Common faults and treatment methods of high-grade garage door are as follows
一、无法用手动开关或遥控器启动驱动装置:
1、 The drive cannot be started with a manual switch or remote control:
1.传动装置未接通电源 2.手动开关或遥控接收板断路 3.运转过度造成电机热保护 4.检查插座、插头、手动开关、保险管熔丝 5.检查手动开关和遥控接收板接线6.调整行程开关的位置以增加行程。
1. The transmission device is not powered on 2. The manual switch or remote control receiving board is open circuited 3. The motor thermal protection is caused by excessive operation 4. Check the socket, plug, manual switch and fuse 5. Check the wiring between the manual switch and the remote control receiving board 6. Adjust the position of the travel switch to increase the travel.
二、门的关闭不当或打开不当:
2、 Improper closing or opening of doors:
1.错误调整行程开关位置 2.调整行程开关位置以增加行程。
1. Adjust the travel switch position incorrectly 2. Adjust the travel switch position to increase the travel.
三、手动开关可以控制驱动装置,但遥控器无法:
3、 The manual switch can control the drive, but the remote control cannot:
1.遥控器未对码 2.遥控系统故障 3.根据说明书说明完成对码操作 4.更换遥控器内部电池
1. The remote control does not match the code. 2. The remote control system is faulty. 3. Complete the code matching operation according to the instructions in the manual. 4. Replace the internal battery of the remote control
5.请维修人员检查接收控制板。
5. Ask the maintenance personnel to check the receiving control board.
四、门未关紧时自动反向运转,或开门未接触行程开关时中途停止运转:
4、 Automatic reverse operation when the door is not closed tightly, or stop operation halfway when the door does not contact the travel switch:
1.开关门阻力比开闭负载力大,会激活障碍物感应系统 2.连杆长度调整不适当 3.离合器拉长不适当,检查门本体和扭弹簧是否平衡,开闭是否灵活 4.增加开闭负载力 5.门关闭时调整连杆长度。
1. The opening and closing resistance of the door is greater than the opening and closing load force, which will activate the obstacle sensing system. 2. The length of the connecting rod is not adjusted properly. 3. The clutch is not stretched properly. Check whether the door body and torsion spring are balanced and whether the opening and closing are flexible. 4. Increase the opening and closing load force. 5. Adjust the length of the connecting rod when the door is closed.
五、门体内单向运行的行程开关损坏或行程开关线短路:
5、 The one-way travel switch in the door body is damaged or the travel switch line is short circuited:
1.光电开关光路上有障碍物,启动负载力调整未到位 2.检查行程开关及行程开关线路 3.清除光电形光路上有障碍物 4.重新调整启动负载力。
1. There are obstacles on the optical path of the photoelectric switch, and the adjustment of the starting load force is not in place. 2. Check the travel switch and travel switch circuit. 3. Remove the obstacles on the photoelectric optical path. 4. Readjust the starting load force.
六、门体冲式行程开关:
6、 Door body impulse travel switch:
1.行程开关损坏,或行程开关线路断路 2.检查行程开关和行程开关线路。
1. The travel switch is damaged or the travel switch circuit is open circuit. 2. Check the travel switch and travel switch circuit.
七、车库外遥控器的作用距离显著小于10米。
7、 The operating distance of the remote controller outside the garage is significantly less than 10m.
1.严重的车库屏蔽2.电池电量不足 3.将天线延伸到车库外部 4.将天线伸向驱动器外部并拉直 5.更换电池。
1. Severe garage shielding 2. Insufficient battery power 3. Extend the antenna to the outside of the garage 4. Extend the antenna to the outside of the driver and straighten it 5. Replace the battery.
以上的精彩内容来自: 高档车库门提供分享,更多的精彩内容请点击进入我们的网站:http://www.jnhsjlm.com,我们会有更多的精彩内容等您查看
The above wonderful content comes from the high-end garage door. For more wonderful content, please click to enter our website: http://www.jnhsjlm.com , we will have more wonderful content for you to see

推荐阅读/ Recommended reading

工业卷帘门的轨道安装需要注意什么呢?轨道是工业门开关运行的主要部件,一旦轨道焊接的不当或是变形,对工业门的整体运行都会带来不小的影响。今天宏顺厂家小技术负责人就来说说门轨

遥控卷帘门常见的问题解决方法! 2021-10-11
定做快速卷帘门有什么需要留意的? 2021-10-08
车库卷帘门定做需要注意什么? 2021-10-06
分析铝合金卷帘门的保养技巧 2021-09-29

【本站图片均由网站所有方提供,部分图片来源于网络,如无意中侵犯了某媒体或个人的知识产权,请来信或来电告之,本网站将立即删除。】

  • 宏顺卷帘门