(1) Open the aluminum alloy rolling door box and check the list of accessories and main parts;

(2)找到现场,找到安装在门洞的线,确定托盘,卷帘门和侧轨的水平安装参考;铝合金卷帘门重庆安装步骤

(2) Find the site, find the center line installed in the center of the door opening, and determine the horizontal installation reference of the tray, rolling shutter door and side rail; Installation steps of aluminum alloy rolling shutter door in Chongqing

(3)根据门框的下边缘,确定平台,卷轴,滚轮组件,滚轮门和侧轨的上下安装标准;

(3) Determine the upper and lower installation standards of platform, reel, roller assembly, roller door and side rail according to the lower edge of door frame;

(4)将支撑板安装在门框上的相应位置.安装支撑板后,确保活门门两端调整法兰之间有2 mm左右的空间;

(4) Install the support plate at the corresponding position on the door frame. After installing the support plate, ensure that there is about 2 mm space between the adjusting flanges at both ends of the valve door;

(5)将铝合金卷帘门的卷轴放置在支撑凸缘中.卷轴的端部由开口销固定.一个人握住卷轴,另外两个调整滚轮门两侧的导轨和密封条.安装位置(门两侧纵梁);

(5) Place the reel of the aluminum alloy rolling shutter door in the support flange. The end of the reel is fixed by the cotter pin. One person holds the reel, and the other two adjust the guide rails and sealing strips on both sides of the roller door. Installation position (longitudinal beams on both sides of the door);

(6)将下颚安装在指定位置.安装前彻底清洁门框的下边缘,并在下颚上涂上双面胶.撕下并安装保护纸.

(6) Install the lower jaw at the specified position. Before installation, thoroughly clean the lower edge of the door frame and apply double-sided adhesive tape on the lower jaw. Remove and install the protective paper

(7)从卷帘门两端的顶端卷起卷帘门,将导轨两侧的顶端滑入导轨,然后将两个侧轨和密封条连接到横梁上门两侧纵向(现场固定有攻丝和攻丝)一旦完成,确保卷帘d可以平稳地提升;

(7) Roll up the rolling shutter door from the top of both ends of the rolling shutter door, slide the top of both sides of the guide rail into the guide rail, and then connect the two side rails and sealing strips to the beam. Once the longitudinal (tapping and tapping are fixed on site) on both sides of the door is completed, ensure that the rolling shutter D can be lifted smoothly;

(8)拉动卷帘到锁定位置,插入定位销上的轴端(双孔)的凸缘和插入在另一端的凸缘定位销(参见图1) . ),将窗帘管转向门.轻轻转动以取下上部位置销(注意此时:不能松开手,以免盲转并搓手);安装卷帘门,你可以设置比赛上下卷帘门,保证了卷帘门的开启和关闭是轻,,准确,可靠.

(8) Pull the roller shutter to the locking position, insert the flange of the shaft end (double hole) on the positioning pin and the flange positioning pin inserted at the other end (see Figure 1)), turn the curtain tube to the door. Turn it gently to remove the upper positioning pin (Note: at this time, do not loosen your hand to avoid blind rotation and rub your hand); Install the roller shutter door, you can set up the upper and lower roller shutter doors of the competition to ensure that the opening and closing of the roller shutter door is light, safe, accurate and reliable

(9)调试方法:用双手握住手柄,上下推动卷帘门,调节扭簧的力度.打开门(略微向上的帮助),添加太多.

(9) Debugging method: hold the handle with both hands, push the rolling shutter door up and down, and adjust the force of the torsion spring. Open the door (with the help of slightly upward), and add too much

增加和减去弹簧力的方法:插入定位销,松开帘管连杆上的螺丝,将连接带从帘管上分离,然后向关闭方向施力,门的打开方向是力减小.

Methods to increase and decrease the spring force: first insert the locating pin, loosen the screw on the connecting rod of the curtain pipe, separate the connecting belt from the curtain pipe, and then apply force in the closing direction. The opening direction of the door is to reduce the force

(10)安装完成后,清理站点.

(10) After installation, clean up the site

以上就是济南卷帘门厂http://www.jnhsjlm.com为大家介绍的内容，感谢您在百忙之中查看我公司的信息内容，如果您想要了解的更多，欢迎您来电进行咨询!

The above is Jinan rolling shutter door factory http://www.jnhsjlm.com Thank you for checking the information of our company in your busy schedule. If you want to know more, you are welcome to call for consultation!