如今生活中使用到的车库,还有一些小型的门店,均使用方便的电动卷帘门。下面济南卷帘门厂来看看电动卷帘门怎么调位。

The garages and some small stores used in daily life now use convenient electric roller shutter doors. Next, Jinan Rolling Door Factory will see how to adjust the position of the electric rolling door.

1.电动卷帘门主要是运用电机以及卷筒芯轴之间的传动链条进行连接的,通常情况下电动卷帘门是采用螺钉固的方式将其置于链轮支架板上的。因此若是我们需要更换换电机,在这之前就需要把卷帘门调制其低端,或者是采用支架将卷帘的方式将门撑住。这样做的目的就是当卷帘门的制动是靠电机本体上的制动器来起作用,电机拆除后,卷帘门则没有制动而自动下滑;其次还能够使传动链条放松,方便将链条取下。

1. The electric roller shutter is mainly connected by the drive chain between the motor and the drum mandrel. Generally, the electric roller shutter is fixed on the sprocket support plate by screws. Therefore, if we need to replace the motor, we need to adjust the low end of the shutter door or support the shutter door with a bracket. The purpose of this is that when the brake of the roller shutter door is operated by the brake on the motor body, after the motor is removed, the roller shutter door will slide automatically without braking; Secondly, it can also make the transmission chain loose and easy to take down the chain.

2.更换电机的步骤:将电机接线做好标记然后拆除,将电机地脚螺丝拧松将传动链条摘下,较后将电机地脚螺丝拆除将电机取出;新电机安装顺序相反,但要注意,电机安装好后,其本体上的环形手拉链条应自然垂直向下,不得有卡阻现象。

2. Steps to replace the motor: mark the motor wiring and remove it, loosen the motor anchor screw and remove the drive chain, and then remove the motor anchor screw to take out the motor; The installation sequence of the new motor is opposite, but it should be noted that after the installation of the motor, the circular hand zipper strip on its body should be naturally and vertically downward without jamming.

3.电机更换完毕后,检查线路、机械机构均无问题,卷帘门下方无障碍物,门下禁止通行,确认后开始试车调试限位。重庆电动门的限位机构是安装在电机外壳上,称为限位螺套滑块式。

3. After the replacement of the motor, check that there is no problem with the circuit and mechanical mechanism, there is no obstacle under the roller shutter door, and no passage is allowed under the door. After confirmation, start the commissioning and limit. The limit mechanism of Chongqing electric door is installed on the motor housing, which is called the limit screw sleeve slider type.

试机前应先松开限位机构上的锁紧螺钉,然后用手拉动环形链条使门帘离地面1米左右,先试停按键,观察卷门升、停、降各功能是否灵敏可靠。

Before the machine test, loosen the locking screw on the limit mechanism, and then pull the circular chain by hand to make the door curtain about 1 meter from the ground. First try to stop the button, and observe whether the functions of the rolling door are sensitive and reliable.

若正常即可将门帘上升或下降到确定的位置,然后旋转限位螺套,调整碰微动开关滚轮,听到滴答声后,拧紧锁紧螺钉。反复调试,使限位达到较佳位置时,再将锁紧螺钉用力旋紧即可。更多相关内容就来我们网站http://www.jnhsjlm.com咨询吧！

If it is normal, you can raise or lower the door curtain to the determined position, then rotate the limit screw sleeve, adjust and touch the microswitch roller, and tighten the locking screw after hearing the click. After repeated adjustment, when the limit reaches a better position, tighten the locking screw firmly. Come to our website for more relevant content http://www.jnhsjlm.com Ask!