卷帘门是现在许多大型或者门面所需要安装的一种门，收缩方便，并且节省空间。它是以多关节活动的门片一片片并联拼接而成。下面就让济南卷帘门厂带大家一起去学习2种类型的卷帘门安装步骤。

Rolling shutter doors are now a type of door that many large shopping malls or doorways need to install, which is convenient to shrink and saves space. It is formed by parallel splicing of multi joint movable door pieces one by one. Let's take Jinan Rolling Curtain Door Factory to learn the installation steps of two types of rolling curtain doors.

电动卷帘门安装方法和步骤：

Installation method and steps of electric roller shutter door:

1、先在需要安装的门框框口位置画出线。表明尺寸大小，然后找工作人员设计出合适的电动卷帘门，这里值得注意的一点是框内高度比门扇的高度要高一点点。

1. First, draw a line at the position of the door frame opening to be installed. Indicate the size, and then find the staff to design a suitable electric roller shutter door. It is worth noting that the height inside the frame is slightly higher than the height of the door leaf.

2、先把电动卷帘门的门框固定，这里要先拆掉门框下部的固定板。(注意：洞口两侧地面要预留凹槽，经校正合格后，固定木楔，门框铁脚与预埋铁板件焊牢。用水泥砂浆或强度不低于10MPa细石混凝土嵌塞牢固即可。)

2. First fix the door frame of the electric roller shutter door. Here, first remove the fixing plate at the lower part of the door frame. (Note: Grooves should be reserved on the ground on both sides of the opening. After being calibrated to be qualified, the wooden wedge should be fixed, and the door frame iron feet should be welded firmly with the embedded iron plate. It is sufficient to use cement mortar or fine aggregate concrete with a strength of not less than 10 MPa to plug firmly.)

3、安装电动卷帘门扇主体门扇。一定要保证电动卷帘门与墙体结成整体，封闭性要做好，再粉刷洞口及墙体。粉刷完毕后，门缝应均匀平整，开启电动卷帘门应该自由轻便，不得有过紧、过松和反弹现象。

3. Install the main door leaf of the electric roller shutter door leaf. It is necessary to ensure that the electric roller shutter door is integrated with the wall, and the sealing property should be well done before painting the opening and wall. After finishing the painting, the door seam should be uniform and smooth, and the electric roller shutter door should be opened freely and easily, without excessive tightness, looseness, and rebound.

防火卷帘门安装方法和步骤：

Installation method and steps of fireproof rolling shutter door:

1、按设计型号，查阅产品说明书和电气原理图。检查产品表面处理和零附件。量测产品各部位基本尺寸。检查门洞口是否与卷帘门尺寸相符;导轨、支架的预埋件位置、数量是否正确。

1. Refer to the product manual and electrical schematic diagram according to the design model. Check the product surface treatment and accessories. Measure the basic dimensions of each part of the product. Check whether the door opening matches the size of the roller shutter door; Whether the position and quantity of embedded parts of guide rails and supports are correct.

2、测量洞口标高，弹出两导轨垂线及卷筒线。

2. Measure the elevation of the opening and snap the vertical lines of the two guide rails and the center line of the drum.

3、将垫板电焊在预埋铁板上，用螺丝固定卷筒的左右支架，安装卷筒。卷筒安装后应转动灵活。

3. Weld the base plate onto the embedded iron plate, fix the left and right supports of the drum with screws, and install the drum. The reel should rotate flexibly after installation.

4、安装减速器和传动系统。

4. Install the reducer and transmission system.

5、安裳电气拴街系统。

5. Anshang Electric Street Connection System.

6、空载试车。

6. No-load test run.

7、将事先装配好的帘板安装在卷筒上。

7. Install the pre assembled curtain plate on the drum.

8、安装导轨。按图纸规定位置，将两侧及上方导轨焊牢于墙体预埋件上，并焊成以体，各导轨应在同一垂直平面上。

8. Install the guide rail. According to the position specified in the drawing, weld the guide rails on both sides and above onto the wall embedded parts, and weld them into a body. Each guide rail should be in the same vertical plane.

9、安装水幕喷淋系统，并与总控制系统连接。

9. Install a water curtain spray system and connect to the main control system.

10、试车。先用手去试运行，再用电动机启闭数次，调整无卡住、阻滞及异常。

10. Test run. First, use your hand to conduct a trial run, and then start and close the motor several times to adjust it to be free of jamming, blocking, and abnormalities.

以上就是问题的相关解答了，您对此有怎样的疑惑或者需求就来我们网站http://www.jnhsjlm.com进行咨询了解吧！

The above is the relevant answer to the question. If you have any doubts or needs about this, please come to our website http://www.jnhsjlm.com Get to know through consultation!